Tag Archives: Multimode Fiber

The Specific Instructions of Optical Fiber Patch Cord

Share

Optical fiber communication refers to modulate voice, video and data signals to the fiber patch cord as a communication transmission medium. The optical fiber can be divided into multimode fiber and single mode fiber.

Single Mode Fiber Patch Cord

The central glass core of single mode fiber is fine (core diameter is usually 9 or 10μm), it only can transfer one mode light. The mode dispersion is small, and it is for remote communication, but it plays a major role in the chromatic dispersion so that the spectral width of the single mode fiber has a higher light stability and the requirement that the spectral width is narrower and better stability. 1000 Mb/s fiber optic transmission distance is 550m-100km. As we all know, we commonly see 9/125μm single mode optical fiber in the market. And single mode 9/125um fiber optic patch cables are recommended for Fast, Gigabit, 10G Ethernet or SONET OC3-OC192 rate optical connections. Low prices make the 9/125um fiber attractive for in-building projects too, because of the reliability and choice of using a single-strand of fiber for same communications (simplex cords are used on Bi-Directional data links).

Multimode Fiber Patch Cord

The central glass core of Multimode fiber is coarse (50 or 62.5μm), multiple modes of light can pass. However, its mode dispersion is among large, which limits the frequency of the transmitted digital signal, and with the increase in distance will be more severe. Multi-mode fiber transmission distance is relatively recent, generally only a few kilometers. 1000 Mb/s fiber optic transmission distance is 220m-550m. In general, we can find 62.5/125um Multi-mode fiber optic cable in the market. 62.5/125um multimode fiber cables are recommended for Fast Ethernet and up to OC3/STM1 rate optical connections. They can also be used for Gigabit Ethernet multi-mode connections on distances less than 275 meters. 62.5/125um fiber is most used inside buildings.

Types of Fiber Patch Cord

In the network wiring, the more applications optic fiber has three types, there are 62.5μm/125μm multimode fiber, 50μm/125μm multimode fiber, and 9μm/125μm single mode fiber. According to the rate and transmission distance, we can distinguish and choose single/multimode optic fiber. Tied the fiber bundle, outside has the protective housing, which is called fiber cable. According to different application environments, the cable can be divided into indoor and outdoor fiber optic cable.

Fiber refers that the fiber jumper with a desktop computer or device connected directly to facilitate the connection and manage the device. Fiber jumpers are also divided into two multimode and single-mode, which are connected with single mode and multimode fiber. Jumper for an active connection cable between the two devices without connectors (as distinguished: patch (patch cord) is one or both ends with connectors; jumper is at both ends of the cable has a fiber optic connectors, the device can be directly connected, but only one end of the fiber pigtail connector and the other end to the fiber splicing).

Fiber Patch Cord Connector Types

Fiber patch cord connector shape can be divided into FC, SC, ST, LC, etc. According TO ferrule grinding mode, it can be divided into PC (plane), UPC (spherical surface), APC (8 degrees inclined plane ) and other (cable optical transceiver general requirements FC / APC connector). According to the type of optical fiber, it can be divided into the single mode optical fiber, 50/125 multimode, 62.5/125 multimode and Gigabit, etc. According to the optical fiber connetor, we commonly see LC, SC fiber patch cord in the market,  the following products are LC-SC fiber in our online store, if you have interest, you can go to our store to have a see.

LC SC Fiber patch cord

Fiber patch cord products are widely applied, it applies in the communications room, fiber to the home, local area networks, fiber optic sensors, fiber optic communication systems, fiber optic transmission equipment connected, defense readiness and so on. Apply to cable television, telecommunications networks, computer networks and optical fiber test equipment. Broken down mainly used in several ways.

The Progress of Multimode Fiber

Share

In 1976, Corning developed 50/125μm by the graded-index multimode fiber and 1983 by Lucent Bell Labs developed 62.5/125μm graded-index multimode fiber, they are two larger amount of Multimode Fiber. The cladding diameter and mechanical properties of these two fibers are same, but different transmission characteristics. They can provide such as Ethernet, Token Ring and FDDI protocols specified in the standard distance required bandwidth, and it can be upgraded to Gb/s rate.

The new multimode fiber standard grades issued by ISO / IEC 11801, Multimode fiber is divided into four categories, OM1, OM2, OM3, OM4. OM1 and OM2 refer to traditional 62.5/125μm and 50/125μm multimode fiber. OM3 and OM4 refer to the new Gigabit 50/125μm multimode fiber.

62.5/125μm Graded-index Multimode fiber(OM1,OM2)

Common 62.5/125μm graded-index multimode fiber is the IEC-60793-2 fiber optic products specification Alb type. As the core diameter and a numerical aperture of 62.5/125μm fiber is greater, which has a strong anti-concentrating ability and bending characteristics, especially in the 20th century, before the mid-1990s, the lower the rate of the LAN, less demanding on the fiber bandwidth, thus making this fiber to obtain the most widely used, becomes 20 years between the mid-1980s to the mid-1990s mainstream products in most countries data communications fiber market. Belong OM1 and OM2 fiber types of Alb full power injection (OFL) bandwidth respectively 200/500MHz.km (850/1300nm) 500/500MHz.km (850/1300nm).

Now you can see the follow products about 62.5 Multimode Fiber

Duplex OM1 62.5/125 Dia2.5mm Fiber Patch Cable

SMA905- SMA905 Duplex OM1 62.5/125 Dia2.5mm Fiber Patch Cable from Fiberstore

50/125μm graded-index multimode fiber(OM1,OM2)

Common 50/125μm OM2 Fiber graded-index multimode fiber is the IEC-60793-2 fiber optic products specification Ala.1 type. Historically, in order to reduce as much as possible the cost of the LAN system, widely used inexpensive LED as the light source, rather than expensive LD. Since the LED output power is low, the divergence angle is much larger than LD, while the core diameter and a numerical aperture of 50/125μm multimode fiber are relatively small, is not conducive to efficient coupling with the LED, as large core diameter and numerical aperture of 62.5/125μm (Alb class) fiber enables more light power coupled into the fiber link to, therefore, 50/125μm graded-index multimode fiber in the mid-90s as good as 62.5/125μm (Alb class) that is widely used fiber.

Since the 20th century, a local area network developed up to lGb / s rate, it didn’t meet the requirement 62.5/125μm OM1 Fiber bandwidth with LED light source. Compared with 62.5/125μm multimode fiber, 50/125μm multimode fiber core diameter and a numerical aperture smaller, 50/125μm gradient in the number of multi-mode fiber conduction mode refractive index of about 62.5/125μm multimode fiber conduction mode 1/2.5, thus effectively reducing the modal dispersion of a multimode optical fiber, such that the bandwidth is significantly increased production costs .50/125μm multimode optical fiber is reduced to about 1/3. So make it again been widely used. IEEE802.3z Gigabit Ethernet standard provides 50/125μm multimode and 62.5/125μm multimode fiber can be used as a transmission medium using Gigabit Ethernet. But for the new network is generally preferred 50/125μm multimode fiber. Belong OM1 and OM2 fiber types are Ala. 1 full power injection (OFL) bandwidth respectively 200/500MHz.km (850/1300nm) and 500/500MHz.km (850/1300nm)

OM3 Fiber

Traditional OM1 and OM2 multimode fiber from the standard mode and design are based LED, as the operating wavelength of 850 nm, a low price VCSEL (Vertical Cavity Surface Emitting Laser) and the emergence of wide application, 850nm importance window increased. VCSEL can be lower than the price of long-wavelength lasers to improve network speed to the user. 50/125μm multimode fiber has a higher bandwidth 850nm window, low price VCSEL can support longer transmission distances for Gigabit Ethernet protocol, and the high rate support longer distances. With the improvement of network speed and size, modulation rates up to 10Gb/s short-wavelength VCSEL laser light sources become one of the high-speed network. Since the difference between the two light-emitting devices, optical fibers must transform itself to adapt to changes in light. In order to meet the needs of 10 Gb / s transfer rate, the International Organization for Standardization / International Electrotechnical Commission (ISO/IEC) and the Telecommunications Industry Alliance (TIA) joint drafting of a new generation of 50 μm core multimode fiber standard. ISO/IEC in the new multi-mode fiber grade they will develop a new generation of multi-mode fiber is zoned 0M3 category (IEC standard A1a.2)

OM4 Fiber

OM4 fiber is optimized for the 50μm core multimode fiber, currently, the OM4 (IEC standard A1a.3) criteria is actually an upgraded version of an OM3 multimode fiber. Compared with standard OM3 OM4 fiber, fiber bandwidth indicators just do upgrade. That OM4 standards are made to improve the 850nm wavelength effective modal bandwidth (EMB) and the full bandwidth of the injection (OFL) compared to OM3 fiber.

The Characteristics Of Single mode Fiber and Multimode Fiber

Share

Fiber optic cable is the most common and important transmission medium in optical communication system. It consists of a single glass core, the cladding layer close to the core, a primary coating layer and a protective layer composed of plastic cap.(Cylindrical fiber, the core, cladding and coating layers composed of three parts.) Core and the cladding layer consists of two different optical properties of the medium constituting the medium refractive index of light than the interior of a surrounding medium high refractive index. In the periphery of the package as the cover layer of opaque material, as the light is prevented from escaping from the surface during interspersed. Fiber optic cable has two types: single mode fiber and multimode fiber.

Multimode Fiber

When the geometry of the fiber is much larger than the wavelength of light (about lμm), optical transmission process will be a significant presence of dozens or even hundreds of transport modes, such as the fiber is called multimode fiber.

Due to different propagation modes having different phase propagation velocity, thus, long-distance transmission is generated through mode dispersion (after long-distance transmission delay difference is generated, resulting in the optical pulse broadening). Side mode dispersion will narrow the bandwidth of multimode fiber, the transmission capacity is reduced, and therefore, multi-mode fiber is only suitable for low speed, short-distance optical fiber communication, data communication is currently a large number of multi-mode fiber local area network.

Main products and application performance of multimode fiber in the following table:

Multimode Fiber
The related products about 62.5/125mm multimode fiber from fs.com, it is below:

Duplex OM1 62.5 125 Fiber Patch Cable

The product about  50/125mm OM2 multimode fiber

Duplex OM2 50 125 Fiber Patch Cable

Single Mode Fiber 

When the geometry of the fiber is small, and the wavelength of the same order as the core diameter in the range of 4-10μm, the optical fiber allows only one mode (basic mode) in which the transmission, the remaining high-order mode are all turned off, so that said single mode fiber. Avoid the mode dispersion single mode fiber, suitable for large-capacity long-distance transmission.

IEC 60793-2 and IEC 60793-2-50 single mode fiber will be divided into B1.1, B1.2, B1.3, B2, B4, B5, B6 and other categories, ITU-T also G.652, G .653, G.654, G.655, G.656, G.657 and other recommendations were standardized definition and characteristics of various single mode fiber, and each part of the GB / T 9771 with reference to IEC 60793-2-50 ITU-T G.65x series formulation.

A given type of single mode fiber, the mode field diameter by (also called effective area), the dispersion coefficient, dispersion slope, wavelength cutoff adapted to optimize the parameters, and access ways for different applications.

Related Article: What’s the Difference: Single Mode vs Multimode Fiber

Basic Knowledge About Fiber Optic Cable

Share

From data and voice to security and video conferencing, many of today’s IT infrastructure services rely on fiber optics to transmit information faster, farther, and in greater amounts than ever before. So fiber optics are more and more popularity in our internet. This post will try to answer some of the basic questions about fiber optic cable.

What Is Fiber Optic Cable?

A fiber optic cable is a network cable that contains strands of glass fibers inside an insulated casing. These cables are designed for long distance and very high bandwidth (gigabit speed) network communications.

Fiber Optic Cable

Single Mode vs. Multimode Fiber Optic Cable

Single mode fiber gives you a higher transmission rate and up to 50 times more distance than multimode, but it also costs more. Single-mode fiber has a much smaller core than multimode fiber-typically 5 to 10 microns. Only a single lightwave can be transmitted at a given time. The small core and single lightwave virtually eliminate any distortion that could result from overlapping light pulses, providing the least signal attenuation and the highest transmission speeds of any fiber cable type.

Multimode fiber gives you high bandwidth at high speeds over long distances. Lightwave is dispersed into numerous paths, or modes, as they travel through the cable’s core. Typical multimode fiber core diameters are 50, 62.5, and 100 micrometers. However, in long cable runs (greater than 3000 feet (914.4 ml), multiple paths of light can cause signal distortion at the receiving end, resulting in an unclear and incomplete data transmission. For example, you can try to compare the single mode duplex fiber vs multimode duplex fiber optic cable, and well know they are different.

The Relationship between Fiber Optic Cable and Fiber Patch Cord

A fiber patch cord is a fiber optic cable capped at either end with connectors that allow it to be rapidly and conveniently connected to CATV, an optical switch or other telecommunication equipment. Its thick layer of protection is used to connect the optical transmitter, receiver, and the terminal box. This is known as “interconnect-style cabling”.

What Types of Connectors Should be Used for Fiber Optic Cable?

There are a number of connector styles on the market including LC, FC, MT-RJ, ST, and SC. There are also MT/MTP style connectors that will accommodate up to 12 strands of fiber and take up far less space than other connectors. This connector is intended for use with indoor loose tube no-gel cable constructions. However, the most popular connectors are SC, which pushes in then click when seated, and ST, also known as bayonet style, that is pushed in and twisted to lock. That should be a consideration when making product selections.

What kind of jacket rating and type do you require?

Fiber cable jackets come in many styles. As an example, fiber can be Indoor only, Outdoor only, Indoor/Outdoor, Tactical and it can also have Plenum or Riser ratings.

Jacket color is relatively standardized.

a) Multimode = Orange

b) 50/125um 10G = Aqua

c) Single Mode = Yellow

d) Indoor/Outdoor or Outdoor = Black

e) Custom jacket colors are also available for indoor fiber cables

Conclusion

Whether you are working in a residential or commercial environment. FiberStore offers a wide variety of fiber cables, and other fiber optic cables related products, such as fiber patch cable, fiber optic connector, fiber transceiver. No matter how complex or simple your installation needs are, we have the expertise to provide you with the right products and information for both your fiber optic cable, custom fiber optic assembly and fiber optic connector needs. If you wanna customize your fiber optic products, pls give us a call, our Tel is  +86 (755) 8300 3611 or sent your detail requirement email to sales@fs.com. Thank you!

Different Single Mode and Multimode Fiber Types

Share

Fiber optic cables are the medium of choice in telecommunications infrastructure, enabling the transmission of high-speed voice, video, and data traffic in enterprise and service provider networks. Depending on the type of application and the reach to be achieved, various types of fiber may be considered and deployed, such as single mode fiber type and multimode duplex fiber.

Fiber optic cables come in several different configurations, each ideally suited to a different use or application. Early fiber designs that are still used today include single mode fiber type and multimode fiber. Since Bell Laboratories invented the concept of application-specific fibers in the mid-1990s, fiber designs for specific network applications have been introduced. These new fiber designs – used primarily for the transmission of communication signals – include Non-Zero Dispersion Fiber (NZDF), Zero Water Peak Fiber (ZWPF), 10-Gbps laser optimized multimode fiber, and fibers designed specifically for submarine applications. Specialty fiber designs, such as dispersion compensating fibers and erbium doped fibers, perform functions that complement the transmission fibers. The differences among the different transmission fiber types result in variations in the range and the number of different wavelengths or channels at which the light is transmitted or received, the distances those signals can travel without being regenerated or amplified, and the speeds at which those signals can travel.

There are two different types of fiber optic cable: multimode and single mode fiber type (MMF and SMF). Both are used in a broad range of telecommunications and data networking applications. These fiber types have dominated the commercial fiber market since the 1970’s. The distinguishing difference, and the basis for the naming of the fibers, is in the number of modes allowed to propagate in the core of a fiber. The “mode” is an allowable path for the light to travel down a fiber. A multimode fiber allows many light propagation paths, while a single mode fiber allows only one light path.

In multimode fiber, the time it takes for light to travel through a fiber is different for each mode resulting in a spreading of the pulse at the output of the fiber referred to as intermodal dispersion. The difference in the time delay between the modes is called Differential Mode Delay (DMD). Intermodal dispersion limits multimode fiber bandwidth. This is significant because a fiber’s bandwidth determines its information carrying capacity, i.e., how far a transmission system can operate at a specified bit error rate.

The optical fiber guides the light launched into the fiber core (Figure 1). The cladding is a layer of material that surrounds the core. The cladding is designed so that the light launched into the core is contained in the core. When the light launched into the core strikes the cladding, the light is reflected from the core-to-cladding interface. The condition of total internal reflection (when all of the light launched into the core remains in the core) is a function of both the angle at which the light strikes the core-to-cladding interface and the index of refraction of the materials. The index of refraction (n) is a dimensionless number that characterizes the speed of light in a specific media relative to the speed of light in a vacuum. To confine light within the core of an optical fiber, the index of refraction for the cladding (n1) must be less than the index of refraction for the core (n2).

Fibers are classified in part by their core and cladding dimensions. Single mode duplex fiber have a much smaller core diameter than multimode duplex fiber optic cable. However, the Mode Field Diameter (MFD) rather than the core diameter is used in single mode fiber specifications. The MFD describes the distribution of the optical power in the fiber by providing an “equivalent” diameter, sometimes referred to as the spot size. The MFD is always larger than the core diameter with nominal values ranging between 8-10 microns, while single mode fiber core diameters are approximately 8 microns or less. Unlike single mode fiber type, multimode fiber is usually referred to by its core and cladding diameters. For example, fiber with a core of 62.5 microns and a cladding diameter of 125 microns is referred to as a 62.5/125 micron fiber. Popular multimode product offerings have core diameters of 50 microns or 62.5 microns with a cladding diameter of 125 microns. Single mode fibers also have 125 micron cladding diameters.

A single mode fiber, having a single propagation mode and therefore no intermodal dispersion, has higher bandwidth than multimode fiber. This allows for higher data rates over much longer distances than achievable with multimode fiber. Consequently, long haul telecommunications applications only use single mode fiber type, and it is deployed in nearly all metropolitan and regional configurations. Long distance carriers, local Bells, and government agencies transmit traffic over single mode fiber laid beneath city streets, under rural cornfields, and strung from telephone poles. Although single mode duplex fiber has higher bandwidth, multimode fiber supports high data rates at short distances. The smaller core diameter of single mode duplex fiber also increases the difficulty in coupling sufficient optical power into the fiber. Relaxed tolerances on optical coupling requirements afforded by multimode fiber enable the use of transmitter packaging tolerances that are less precise, thereby allowing lower cost transceivers or lasers. As a result, multimode duplex fiber optic cable has dominated in shorter distance and cost sensitive LAN applications.