Tag Archives: waterproof cable

The Importance Of Waterproof Cable

Share

The basic mechanical failure mechanism for optical fibres is the slow to rapid growth of any glass imperfections in the fibre caused by the fibre being under stress. This ‘fatigue’ phenomenon can be accelerated with the presence of moisture (H2O) molecules at the glass surface of the fibre. So the waterproof for fiber optic cable is very important . Now let us know more info about waterproof cable.

All manufacturers of fibre optic cables intended for use outdoors must address the issue of protecting the fibre’s glass surface from the presence of moisture. Many manufacturers provide the waterproof characteristic to solve the problem. This is because the 250μm primary fibre coating provides only a 62.5μm-thick layer of UV-cured acrylate material as basic protection over the fibre’s glass surface. This UV-cured acrylate material is not chosen by the fibre manufacturers for its optimal resistance to water or its minimal porosity. It is in fact chosen primarily because of its fast processing speed,since a primary cost driver for fibre manufacturers is the draw speed, which is steadily increasing. The very thin UV-cured acrylate layer is porous to water molecules and will permit concentration of OH-ions at the fibre surface, if the fibre is immersed in water.

All plastic materials are porous to varying degrees. The general category of thermoplastic materials commonly used in cable constructions will to some extent absorb water; however, thermoplastic materials certainly do not act as a complete water block. Only materials like metals or glass can provide a true ‘hermetic’ seal. Plastic materials are generally characterised with parameters such as water absorption and absorption of other common solvents such as oils, gasoline, kerosene, etc. This being the case, water molecules cannot be eliminated from the glass surface of any fibres incorporated in a cable having plastic jackets. The issue is to minimise the concentration of water molecules at the glass surface so that stress crack growth effects are minimised.

There are two different designs approaches to water and moisture protection in fibre optic cables.

The loose tube gel-filled cables must prevent water from reaching the 250μm coated fibres. This approach is to ‘waterproof’ the cable by ‘filling’ the empty spaces in the cable with gel, theoretically preventing water from reaching the 250μm coated fibres. To insure that this is accomplished, the ‘filled’ cables are generally subjected to a hosing test to show that water will not flow through a short section (one meter) of cables. The fact that gels can move, flow, and settle, leaves an uncertainty of the filled level of any particular point of a loose-tube gel-filled cable. This uncertainty of the filling is highlighted by the routine practice of water-blocking the loose-tube gel-filled cables at the entrance to splice housings to keep water from migrating from the cable into the splice housing.

The tight-buffered, tight bound indoor/outdoor cables utilise an entirely different design approach to deal with the moisture issue. Rather than attempting to be ‘waterproof’, they are designed to be water tolerant.

Recognising the porosity of plastic materials and the inherent problems of waterproofing a cable, the moisture protection is concentrated at the fibre surface where it is most needed.

Correctly designed harsh environment tight-buffer systems consist of extremely low moisture absorption coefficient materials at the fibre coating. This provides a buffer system thickness of 387μm over the glass which is more than six times as thick as the 62.5μm coating found in the loose-tube cables.

Buffer materials are low-porosity plastics with excellent moisture resistance. This construction very effectively minimises the water molecule and OH-ion concentration level at the glass surface and virtually eliminates the stress corrosion phenomenon. The tight-buffered design also has the great advantage of being a solid, non-flowing, non-moving structure.
The same level of protection remains in place all along the fibre, regardless of installation conditions, environment, or time.
The balance of the tight-buffered, tight bound cable designs is such that it minimises the open spaces available in the cable structure in which water can reside. Even if an outer cable jacket is cut, or water otherwise enters the cable structure, only a very small percentage of the cross-sectional area is open to water.

1,Water penetration refers to the effectiveness of cable in restricting the longitudinal movement of water or moisture along the core. This requirement is primarily intended to localise any water penetration to minimise the adverse effect on cable performance and to prevent water or moisture leaking into joints and terminations that may cause corrosion problems.
2,Additionally, cable installed underground should have a high density compound sheath material (such as poly ethylene) that provides an adequate barrier to moisture entry to the cable core. The addition of a lapped metal tape (‘moisture barrier’) and/or grease or gel within the core (‘filled’ or ‘flooded’ cable) provides even higher protection against moisture entry.

The above considerations is very important and should always be considered. Always refer to the manufacturers specification sheet and follow their installation instructions.

For the diverse requirements of our customer, we are involved in offering a wide assortment of waterproof cables. FiberStore offer these cables at very economical rates in the market. These cables are widely used and are highly demanded in the market due to their water proof nature. In addition to this, we offer these cables in various fiber optic cable specifications as per the requirements of our clients. We provide fiber optic cable products(such as duplex fiber cable,simplex fiber optic cable) are absolutely high quality and low price.

An Overview Of The Armored Fiber Cable

Share

Fiber optic cables form one of the most important parts of the networking industry today. Fiber cables are composed of one or more transparent optical fibers enclosed in a protective covering and strength members. Fiber cables are used to transmit data by the mode of light. Various types of fiber cables available are multimode duplex fiber cables, single mode simplex fiber cables, single mode duplex fiber cables, armored fiber cables and plastic optical fiber cables.

What is Armored Fiber Cable

Armored Fiber Cable, is outside the optical fiber is then wrapped in a layer of protective of “armor”, is mainly used to meet the requirements of customers rodent, moisture proof, etc. Armored cable is a power cable made up by assembling two or more electrical conductors, generally held together with an overall sheath. This electrical cable with high protective covering is used for transmission of electrical power, especially for underground wiring needs. However, these cables may be installed as permanent wiring within buildings, buried in the ground, run overhead, or may even be kept exposed. They are available as single conductor cable as well as multi-conductor cables.

Common Armored Fiber Cable

Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.

Armored Flame Retardant Fiber Optic Cable for Indoor/Outdoor Applications

Indoor/outdoor fiber optic cables have been pretty hot in the last several years and there are good reasons for this. For service providers, indoor/outdoor fiber cables really present big time and cost savings. This cable design can come from the outdoor environment and enter a building without the need to switch cable designs to have the flame retardance required indoors. This dual purpose cable can reduce the cost of the terminations and related labor to change cable designs.

The development of dry water blocking core technology has also helped indoor/outdoor fiber cable development. This dry core technology uses water swellable materials to block the flow of moisture in the longitudinal direction.We also provide other types of fiber optic cable,such as the waterproof cable,waterproof fiber pigtail cable can be used in harsh environment. It is mainly used in outdoor connection of the optical transmitter. Waterproof fiber pigtail is designed with a stainless steel strengthened waterproof unit and armored outdoor PE jacketed cables.

Note:If you want to know more detail fiber optic cable specifications of armored fiber cable,you can visit the armored fiber cable products website in FiberStore.Every fiber optic cables have the different specifications,and if you have some questions of fiber optic cable specifications,pls contact us.