Tag Archives: fusion splicers

A Good Fiber Optic Cleaver Helps Cut Out Costly Mistakes

Share

To get good fiber optic splices or terminations, especially when using the pre-polished connectors with internal splices, it is extremely important to cleave the fiber properly. If the fiber ends are not precisely cleaved, the ends will not mate properly. To prepare a fiber end for a connector or splice, the end of the fiber must be cleaved to a 90 degree flat end. For technicians the problem is that the end of the fiber strand is so small that it is impossible to tell with the naked eye whether the strand has a flat end. So in order for this to happen, you must use a cleaving tool called fiber optic cleaver. Some knowledge of fiber optic cleaves will be provided in this article.

good and bad fiber cleave

What Is Fiber Optic Cleaver?
A cleave in an optical fiber is a deliberate, controlled break, intended to create a perfectly flat end face, perpendicular to the longitudinal axis of the fiber. A fiber optic cleaver is a tool that holds the fiber under low tension, scores the surface at the proper location, then applies greater tension until the fiber breaks. Usually, after the fiber has been scored, the technician will use a cleaver either bend or pull the fiber end, stressing the fiber. This stress will cause the fiber to break at the score mark, leaving a 90 degree flat end if all goes well. So the cleaver doesn’t cut the fiber. In fact, it just breaks the fiber at a specific length.

Two Types of Fiber Optic Cleavers
We know that the closer to 90 degrees the cleave is, the more success you will have with matching it to another cleaved fiber to be spliced or mated by a connector. So it’s important to use the proper tool with good technique to consistently achieve a 90 degree flat end. Good cleavers are automatic and produce consistent results, irrespective of the operator. The user need only clamp the fiber into the cleaver and operate its controls. Some cleavers are less automated, making them more dependent on operator technique and therefore less predictable. There are two broad categories of fiber optic cleavers, scribe cleavers and precision cleavers.

Scribe Cleavers
A traditional cleaving method, typically used to remove excess fiber from the end of a connector before polishing, uses a simple hand tool called a scribe. Scribe cleavers are usually shaped like ballpoint pens with diamond tipped wedges or come in the form of tile squares. The scribe has a hard, sharp tip, generally carbide or diamond, that is used to scratch the fiber manually. Then the operator pulls the fiber to break it. Since both the scribing and breaking process are under manual control, this method varies greatly in repeatability. Most field and lab technicians shy away from these cleavers as they are not accurate. However, if in skilled hands, this scribe cleaver offer significantly less investment for repairs, installation, and training classes.

Scribe

Precision Cleavers
Precision cleavers are the most commonly used cleavers in the industry. They use a diamond or tungsten wheel/blade to provide the nick in the fiber. Tension is then applied to the fiber to create the cleaved end face. The advantage to these cleavers is that they can produce repeatable results through thousands of cleaves by simply just rotating the wheel/blade accordingly. Although more costly than scribe cleavers, precision cleavers can cut multiple fibers while increasing speed, efficiency, and accuracy. In the past, many cleavers were scribes, but over time, as fusion splicers became available and a good cleave is the key to low splice loss, precision cleavers were developed to support various applications and multiple fiber cleaving with blades that have a much longer life span.

Precision Cleaver

Which One to Use: Scribe Cleaver or Precision Cleaver?
While both types perform the functions above, the difference between the two categories of cleavers is the percentage yield of good cleaves. An experienced fiber optic technician will achieve approximately 90% good cleaves with a scribe cleaver, while the precision cleaver will produce 99% good cleaves. The difference doesn’t seem like much so you may hardly to make a specific decision. My suggestion is to buy precision cleavers if you plan to use a lot of mechanical splices or pre-polished splice/connectors. It will pay for itself in no time. If you decide to use the inexpensive scribe cleavers, you must learn how to use it properly. Follow directions, but also do what comes naturally to you when using the device, as they are sensitive to individual technique. Inspect the fibers you cleave to see how good they are and keep practicing until you can make consistently good cleaves.

To find pricing, information and more information on the different fiber optic cleavers currently available, please visit www.fs.com. Sign up to get informative news, posts and deals in regards to current products in the fiber optic field. Or you also can contact our friendly staff members at sales@fs.com to learn more about all the fiber optic cleavers with the best value that are present in the industry today.

Original article source:
http://www.fs.com/blog/a-good-fiber-optic-cleaver-helps-cut-out-costly-mistakes.html

The Era of Fusion Splicing Is Coming

Share

Fusion splicingAs fiber deployment has become mainstream, splicing has naturally crossed from the outside plant (OSP) world into the enterprise and even the data center environment. Fusion splicing involves the use of localized heat to melt together or fuse the ends of two optical fibers. The preparation process involves removing the protective coating from each fiber, precise cleaving, and inspection of the fiber end-faces. Fusion splicing has been around for several decades, and it’s a trusted method for permanently fusing together the ends of two optical fibers to realize a specific length or to repair a broken fiber link. However, due to the high costs of fusion splicers, it has not been actively used by many people. But these years some improvements in optical technology have been changing this status. Besides, the continued demand for increased bandwidth also spread the application of fusion splicing.

New Price of Fusion Splicers
Fusion splicers costs have been one of the biggest obstacles to a broad adoption of fusion splicing. In recent years, significant decreases in splicer prices has accelerated the popularity of fusion splicing. Today’s fusion splicers range in cost from $7,000 to $40,000. The highest-priced units are designed for specialty optical fibers, such as polarization-maintaining fibers used in the production of high-end non-electrical sensors. The lower-end fusion splicers, in the $7,000 to $10,000 range, are primarily single-fiber fixed V-groove type devices. The popular core alignment splicers range between $17,000 and $19,000, well below the $30,000 price of 20 years ago. The prices have dropped dramatically due to more efficient manufacturing, and volume is up because fiber is no longer a voodoo science and more people are working in that arena. Recently, more and more fiber being deployed closer to the customer premise with higher splice-loss budgets, which results in a greater participation of customers who are purchasing lower-end splicers to accomplish their jobs.

More Cost-effective Cable Solutions
The first and primary use of splicing in the telecommunications industry is to link fibers together in underground or aerial outside-plant fiber installations. It used to be very common to do fusion splicing at the building entrance to transition from outdoor-rated to indoor-rated cable, because the NEC (National Electrical Code) specifies that outdoor-rated cable can only come 50 feet into a building due to its flame rating. The advent of plenum-rated indoor/outdoor cable has driven that transition splicing to a minimum. But that’s not to say that fusion splicing in the premise isn’t going on.

Longer distances in the outside plant could mean that sticking with standard outdoor-rated cable and fusion splicing at the building entrance could be the more economical choice. If it’s a short run between building A and B, it makes sense to use newer indoor/outdoor cable and come right into the crossconnect. However, because indoor/outdoor cables are generally more expensive, if it’s a longer run with lower fiber counts between buildings, it could ultimately be cheaper to buy outdoor-rated cable and fusion splice to transition to indoor-rated cable, even with the additional cost of splice materials and housing.

As fiber to the home (FTTH) applications continue to grow around the globe, it is another situation that may call for fusion splicing. If you want to achieve longer distance in a FTTH application, you have to either fusion splice or do an interconnect. However, an interconnect can introduce 0.75dB of loss while the fusion splice is typically less than 0.02dB. Therefore, the easiest way to minimize the amount of loss on a FTTH circuit is to bring the individual fibers from each workstation back to the closet and then splice to a higher-fiber-count cable. This approach also enables centralizing electronics for more efficient port utilization. In FTTH applications, fusion splicing is now being used to install connectors for customer drop cables using new splice-on connector technology and drop cable fusion splicer.

FTTH drop cable fusion splicer

A Popular Option for Data Centers
A significant increase in the number of applications supported by data centers has resulted in more cables and connections than ever, making available space a foremost concern. As a result, higher-density solutions like MTP/MPO connectors and multi-fiber cables that take up less pathway space than running individual duplex cables become more popular.

Since few manufacturers offer field-installable MTP/MPO connectors, many data center managers are selecting either multi-fiber trunk cables with MTP/MPOs factory-terminated on each end, or fusion splicing to pre-terminated MTP/MPO or multi-fiber LC pigtails. When you select trunk cables with connectors on each end, data center managers often specify lengths a little bit longer because they can’t always predict exact distances between equipment and they don’t want to be short. However, they then have to deal with excess slack. When there are thousands of connections, that slack can create a lot of congestion and limit proper air flow and cooling. One alternative is to purchase a multi-fiber pigtail and then splice to a multi-fiber cable.

Inside the data center and in the enterprise LAN, 12-fiber MPO connectors provide a convenient method to support higher 40G and 100G bandwidth. Instead of fusing one fiber at a time, another type of fusion splicing which is called ribbon/mass fusion splicing is used. Ribbon/mass fusion splicing can fuse up to all 12 fibers in one ribbon at once, which offers the opportunity to significantly reduce termination labor by up to 75% with only a modest increase in tooling cost. Many of today’s cables with high fiber count involve subunits of 12 fibers each that can be quickly ribbonized. Splicing those fibers individually is very time consuming, however, ribbon/mass fusion splicers splice entire ribbons simultaneously. Ribbon/mass fusion splicer technology has been around for decades and now is available in handheld models.

Ribbon/Mass Fusion Splicer

Conclusion
Fusion splicing provides permanent low-loss connections that are performed quickly and easily, which are definite advantages over competing technologies. In addition, current fusion splicers are designed to provide enhanced features and high-quality performance, and be very affordable at the same time. Fiberstore provides various types and uses of fusion splicers with high quality and low price. For more information, please feel free to contact us at sales@fs.com.